球磨时间对钛酸钡介电性能的影响

通过改变混料的秩序以及采用沉降、水煮损耗、温度特性、电导率和化学分析等测试手段，研究了制备钛酸钡的球磨工艺中球磨时间对钛酸钡粉体均匀性及钛酸钡介电性能的影响。研究结果表明：采用不同的球磨时间制得的钛酸钡性能差别较大，球磨时间达12小时时，能减少球磨引起的团聚，极大地改善了固相合成BaTiO3粉体均匀性，并最终提高了钛酸钡的介电性能。     

浅析加快300 MW机组启动速度的方法及措施

随着电网的装机容量日益增大,机组的启动次数也在逐日增多。从保证机组安全经济运行的角度出发,结合笔者直接或间接参与制定的技术措施,简要分析了影响机组启动速度的因素和改善措施,以期为其他发电厂在机组启动方面提供一些参考和建议。     

Magnetoelectric coupling in multiferroic BiFeO3 by co-doping with strontium and nickel

We report the effects of the Sr²⁺ and Ni²⁺ co-doping of BiFeO₃ on the crystal structure and multiferroic properties of Bi_1?xSr_xFe_1-yNi_yO₃ (x?=?0.05, 0.0?≤?y?≤?0.10, and Δy?=?0.05) that is synthesized using assisted high-energy ball milling. The mixtures of Bi₂O₃, Fe₂O₃, SrO and NiO were milled for 5?h, pressed at 900?MPa, and sintered at 800?°C in order to obtain cylindrical test pieces. X-ray diffraction and Rietveld refinement elucidated the effects of Sr²⁺ and Ni²⁺ on the crystal structure. Co-doping with SrNi in suitable proportions stabilizes rhombohedral BiFeO₃. High contents of Ni²⁺ promote the precipitation of secondary phases in the forms of NiFe₂O₄ and Bi₂₅FeO₄₀. The magnetic behavior was examined by means of vibrating sample magnetometry. The results showed a change in the magnetic order from antiferromagnetic for the undoped sample to the ferromagnetic order for the co-doped samples. This change is attributed to the modulations in the magnetic moment due to crystal structure distortions. All samples show high relative permittivity values, which were enhanced by doping with Sr²⁺. Ni²⁺ cations increase the dielectric dissipation factor; this enhancement is related to their interactions with cations of a different oxidation state, such as Fe³⁺, Fe²⁺, Ni²⁺, Bi³⁺ and Sr²⁺ in the crystal structure of BiFeO₃. The magnetoelectric coupling that was evaluated using magnetodielectric measurements was above 4% at 1?kHz for the higher applied magnetic field of 18?kOe.     

La_(1.8)Ca_(0.2)Mg_(14)Ni_3合金在甲苯溶液中球磨改性后的储氢性能

采用在甲苯介质中球磨以改善La1.8Ca0.2Mg14Ni3的储氢性能。随着球磨时间的增加,合金的吸放氢性能得到显著地提高,在20 h达到最高。其在513 K,4.0 MPa氢压下初次活化时,吸氢质量分数达到了3.95%,在3次活化后,300 K时的吸氢质量分数达到3.85%,在613 K,一个大气压的放氢质量分数在900 s内达到了4.92%。通过XRD和SEM分析,球磨后合金颗粒粒径明显减小且有非晶化趋势。在球磨过程中形成了电子络合体(electrondonor-acceptor,EDA)体系。合金颗粒粒径、非晶化程度和EDA共同作用使球磨20 h的合金表现出最优异的吸放氢性能。     

Fractionation of transgenic corn for recovery of recombinant enzymes

Two germ-separation methods, dry-milling and density separation by flotation, were evaluated for recovering recombinant β-glucuronidase (rGUS) that accumulated primarily in the germ of transgenic corn. The dry-milling process consisted of (i) seed tempering, (ii) degerming with a horizontal-drum degermer/dehuller, (iii) particle size fractionation with standard sieves, (iv) germ and endosperm separation by roller milling and sifting, and (v) removal of hulls by aspiration. Sieves nos. 5, 6, and 7 retained the majority of germ, and subfractions from these sieves were pooled as a germ-rich fraction. Mass balances showed that the germ-rich fraction, which constituted 17% of the total dry-milled corn weight, contained 49% of rGUS activity and 64% of the total recoverable oil. Germ fractionation by flotation was tested as a proof-of-concept method aimed at separating corn fractions based on their difference in specific gravity (sp gr). The process consisted of impact-grinding of corn kernels followed by density separation using 1.15 or 1.3 specific gravity sodium nitrate solution. The oil-containing germ fraction floated, whereas the heavier endosperm fraction sedimented. The flotation method was simpler and resulted in higher enzyme recovery, that is, the germ-rich fraction was 20% (w/w) of the initial corn weight, and accounted for 80% of rGUS activity and 77% of total oil. The sodium nitrate solution did not have an adverse effect on the enzyme activity.     

熔融晶化法制备硅灰石及其粉碎工艺的研究

以二氧化硅和碳酸钙为主要原料,以碳酸钠、氧化硼和氟化钙为助熔剂,采用熔融晶化法制备了硅灰石。研究了不同粉碎工艺条件对制备针状硅灰石的影响。结果表明,熔融晶化法合成的硅灰石其主晶相为-βCaSiO3。对比两种粉碎方式得出,气流粉碎比介质磨粉碎更有利于保护硅灰石针状晶型,获得的硅灰石粉末的长径比比较大,平均长径比为6.89∶1。     

球磨参数及Ni比例对Mg2Ni合金储氢性能影响研究

采用中频感应炉熔炼出铸态Mg2 Ni合金,将Mg2Ni合金与一定量的Ni粉进行混合球磨处理.系统研究在不同Ni粉添加量及球磨时间等条件下所得合金样品的结构及储氢性能.研究表明,随着Ni含量的增大及球磨时间的延长,合金的非晶纳米晶结构逐渐增多;合金的最大放电容量及循环稳定性得到明显提升;合金的表面催化活性及合金体相内的H传输能力都有了显著提高.Ni粉的作用主要在于可促进合金非晶化,同时对合金的放氢过程起到了催化的作用.     

刀具几何角度对高速铣削性能影响的仿真分析

切削力和切削温度是影响刀具耐用度及被加工表面质量的重要因素,其中刀具几何角度在金属切削加工过程中对切屑的形成、切削力的大小以及散热条件等影响很大。因此,合理地选择刀具几何角度对提高刀具使用寿命和生产效率、降低生产成本具有重要意义。以铝合金7075-T651高速铣削为研究对象,借助金属切削工艺软件AdvantEdge对铣削加工进行模拟仿真,得到加工过程中切削力和温度随时间的变化关系,并结合单因素法,分析了不同刀具角度的选择对切削力和切削温度的影响。该结果为高速铣削刀具几何角度的选择提供参考。     

PLC在合金型材铣床改造中的应用

针对某厂合金型材铣床的电气控制系统改造要求，采用FX2N可编程控制器进行控制，取得了很好的效果。